Dielectric Withstand or hipot testing is done by applying high voltage between wire being tested and ground, presumably locomotive chassis. If excess current leakage or if an arc occurs, test fails. Insulation Resistance testing provides numerical value indicating resistance insulation. Information on how hipot testers work can be read below.
High Pots could be AC, DC and conducted sporadically, or at final assembly line stage, etc. Stress assessment results, in general, illustrates Pass Fail basing on current leak. For several systems, this method may bear out risks. Testing medium volt wire might also pose dangers.
Dielectric strength presents maximum electrical field that pure material may withstand underneath ideal setting without tearing down or without experiencing failure with its insulating properties. Theoretical dielectric strength is material intrinsic property on bulk material and independent configuration material or electrodes with which field is put to use. This inherent dielectric withstand corresponds what is being measured using untouched materials under controlled laboratory settings.
At breakdown, electrical fields free bounded electrons. If applied electrical fields are sufficiently high, freed electrons from surrounding radiation might accelerate with velocities which could liberate further electrons during neutral atom molecule collision in a course termed avalanche breakdown. Avalanche Breakdowns take place somewhat quickly, in nanoseconds normally, resulting into an electrically conducive path structure and disrupting electron release throughout an object. For concrete materials, avalanche breakdown event rigorously debase, even demolish said materials insulating potential.
With respect to insulations and dielectric testings differences, none exists. Contrast between insulation and di electric testing does not matter. Dielectric quality basically demonstrates how well an insulator is. About testing, frequency test ought to be controlled by what voltage insulating substance should expect amid its functional period. Which implies you ought keep from DC quality testing aspects that will be utilized for AC 50 or 60 Hertz applications.
While they are just two separate and very different procedures, these terms are wildly thrown around interchangeably in electrical industry. So you cannot easily rely on those names accurately describe what is being tested alongside how test was performed. For example, in Practical Guide Di electric Tests, where Di electric Tests in their definition is an Insulation Resistance tests HiPot tests combination.
Whereas, typically, HiPot tester being used for Di electric Strength Withstand test would suit utilization for an Insulation Resistance test. Specific terminology used would really depend on company you are working, dealing with. If it really matters, you need to read given procedure description itself.
Insulation Resistance test will show DC most of the time. Di electric withstand test will commonly be AC yet can be DC. When one studies AC DC removal as one investigates similar subjects, previous experiments regarding above topic were conducted by research engineers. Final results show both are still required since they offer very distinct information.
An emphasis on these tests interchangeability would trivial because, at the end of the day, most insulated materials go through both as it unwise generally to pigeon hole your substance product into using only one frequency, electrical transmission when most cases it will work for both assuming they have same amount. Using 48v DC system, generally using materials with secondary rating around 600v ac should suffice. Ultimately as long as one does not fail hipot, everyones happy regardless of insulated matter used.
High Pots could be AC, DC and conducted sporadically, or at final assembly line stage, etc. Stress assessment results, in general, illustrates Pass Fail basing on current leak. For several systems, this method may bear out risks. Testing medium volt wire might also pose dangers.
Dielectric strength presents maximum electrical field that pure material may withstand underneath ideal setting without tearing down or without experiencing failure with its insulating properties. Theoretical dielectric strength is material intrinsic property on bulk material and independent configuration material or electrodes with which field is put to use. This inherent dielectric withstand corresponds what is being measured using untouched materials under controlled laboratory settings.
At breakdown, electrical fields free bounded electrons. If applied electrical fields are sufficiently high, freed electrons from surrounding radiation might accelerate with velocities which could liberate further electrons during neutral atom molecule collision in a course termed avalanche breakdown. Avalanche Breakdowns take place somewhat quickly, in nanoseconds normally, resulting into an electrically conducive path structure and disrupting electron release throughout an object. For concrete materials, avalanche breakdown event rigorously debase, even demolish said materials insulating potential.
With respect to insulations and dielectric testings differences, none exists. Contrast between insulation and di electric testing does not matter. Dielectric quality basically demonstrates how well an insulator is. About testing, frequency test ought to be controlled by what voltage insulating substance should expect amid its functional period. Which implies you ought keep from DC quality testing aspects that will be utilized for AC 50 or 60 Hertz applications.
While they are just two separate and very different procedures, these terms are wildly thrown around interchangeably in electrical industry. So you cannot easily rely on those names accurately describe what is being tested alongside how test was performed. For example, in Practical Guide Di electric Tests, where Di electric Tests in their definition is an Insulation Resistance tests HiPot tests combination.
Whereas, typically, HiPot tester being used for Di electric Strength Withstand test would suit utilization for an Insulation Resistance test. Specific terminology used would really depend on company you are working, dealing with. If it really matters, you need to read given procedure description itself.
Insulation Resistance test will show DC most of the time. Di electric withstand test will commonly be AC yet can be DC. When one studies AC DC removal as one investigates similar subjects, previous experiments regarding above topic were conducted by research engineers. Final results show both are still required since they offer very distinct information.
An emphasis on these tests interchangeability would trivial because, at the end of the day, most insulated materials go through both as it unwise generally to pigeon hole your substance product into using only one frequency, electrical transmission when most cases it will work for both assuming they have same amount. Using 48v DC system, generally using materials with secondary rating around 600v ac should suffice. Ultimately as long as one does not fail hipot, everyones happy regardless of insulated matter used.
About the Author:
Get an overview of the factors to consider when selecting a hipot tester supplier and more information about a reputable supplier at http://www.rossengineeringcorp.com/products/measurement/ac-dc-digital-hipots.html now.
Aucun commentaire:
Enregistrer un commentaire